4-Wire Heat Detector with Relay Output WT145,CFT Fire Alarms is specialized in the design, production and sales of the fire alarm systems including both addressable and conventional products. 5600 Series Mechanical Heat Detectors 5601PHeat Detectors for Fire Protective Signaling Systems. The detector shall be either a single-circuit or a dual-circuit type, normally open. The detector shall be rated for activation at either 135°F (57°C) or 194°F (90°C), and shall activate by means of a fixed temperature thermal sensor,
4-wire relay functions. The Model THD-705x Heat Detectors may be interchanged with other Fenwal Series CPD-705X Ionization and Series PSD-715X Photoelectric Smoke Detectors when using multifunction base configuration. TECHNICAL SPECIFICATIONS Table 1 lists the Technical Specifications for Models THD-7052 and THD-7053 Heat Detectors. CONTROL UNITS Best Price Conventional 4 Wire Heat Detector With Nc. No 1.SR-505-4 is 4-Wire network heat detector. 2.Combination rate-of-rise and fixed temperature alarm. 3.MCU processing, eliminate false alarm. 4.Low standby current. 5.Anti-RFI &Anti-EMI. 6.9-35VDC wide operating voltage range. 7.LED flashing visible in 360 degrees direction. 8.Power supply non-polar input. 9.Alarm output is Relay output Conventional Detectors » Pertronic Industries LimitedConventional indicating heat detectors. Static (fixed) threshold:57 °C (blue) or 77 °C (yellow). NZS 4512-compliant READ MORE. Datasheet. Installation Note. IHD*E-V Multi-criteria detector, 4-wire, with photoelectric smoke sensor, heat sensor with 58 °C fixed (static) threshold, sounder, and relay READ MORE. Datasheet
Corporate Headquarters. 13723 Riverport Drive Saint Louis, MO 63043. Production Facility. 1609 Park 370 Place Saint Louis, MO 63042 Conventional Fire Detection - Intelligent Life SafetyConventional Fire Detection Contents System Architecture Control Panel Automatic & Manual Detection Manual Call Points Smoke Detectors Heat Detectors Beam Smoke Detectors Duct Smoke Detector Alarm Devices S3 Electronic Sounders / Strobes S3 Voice Enhanced ABS casing with red LED fire heat Detector indicator Conventional Fire Detectors - Ningbo Sentek Electronics Co Smoke Alarm, Smoke Detector, Fire Detector manufacturer / supplier in China, offering Ce Approved 4 Wire Conventional Photoelectric Smoke Detector Fire Alarm, Wired UL Reed Switches Magnetic Switch (BR-1021), Sentek Aluminum Case Overhead Door Magnetic Contacts Switches Bsd3012 and so on.
Conventional Specialty Detectors, Bases, and Housings. Conventional Manual Stations. Conventional Accessories. Basic functions. Category Duct smoke detectors Technology Addressable. Technology EN 54. Product segment Conventional Products Fire Alarm Systems - UL, ULC, FM D342 Family fourwire duct smoke detector housings. For 1 ft. (30.5cm) to 10 ft. (3 m) ducts with air velocity between 300 ft./min. to 4000 ft./min. (1.52 m/s to 20.3 m/s) Easy duct tube installation through the housing cuts installation time. Detector test and reset without removing covers. Conventional detector range for UL fire alarm systems Eaton2 Wire Opto Heat Detector:UCPT-2W:2 Wire Fixed Heat 135°F Detector:UCHT-2W:2 Wire Fixed Heat 194°F Detector:UCHTI-2W:2 Wire Rate of Rise and Fixed Heat 135°F Detector:UCHR-2W:Conventional Detector Base:CB2E
DCD 135/190 FIXED TEMPERATURE/RATE OF RISE HEAT DETECTOR STANDARD FEATURES bases.Choice of fixed temperature/rate-of-rise 135°F or 190°F heat detector UL Listed spacing up to 60' by 60' 2 or 4 wire base compatibility, relay bases available Highly stable operation, RF/Transient protection Low standby current, 35A nominal F220 Heat Detectors Conventional Detectors, Bases, and Four-wire detector base with sounder for use with the F220 Photoelectric Smoke and Heat Detectors. Base, 4-wire, form A & C relays, 12/24V Commercial Type No. F220-B6C Product No. 4.998.113.024 Four Wire Type Smoke Detectors - AlarmSystemStoreFour Wire Type Smoke Detectors can be used if you're looking to separate out different areas or levels of the building and want to know where a fire may have started. These use two wires for powering the smoke and two more wires to run back to your alarm panel zone. These can also sense heat
conventional mains heat alarm heat sensor alarm many heat detector types . Product Description . Here are our conventional heat detector SR-503 series main features 1.Combination rate-of-rise and fixed temperature alarm 2.MCU processing, eliminate false alarm Simplex - Product SeriesSimplex photo and photo-heat sensors are also UL268 7th Edition listed to meet the latest standards and help you stay fully code compliant. detectors bring many of the proven TrueAlarm analog sensing features to applications where detectors are connected to conventional 2-wire or 4-wire initiating device circuits. Beam Detectors are Smoke, heat & photo-thermal 5 in 1 conventional detector Eaton has a large range of detectors for conventional fire alarm systems designed to meet the demands of nearly any application. In the range, there are two main options either the flexible, easily switchable 5 in 1 detector that brings together all the detection mode or the straightforward single detection mode range. Both options include optical, photo-thermal and heat modes.
4-Wire Rate-of-Rise and Fixed Temperature Heat Detector. Our HM-203HC-4 product is the 4-wire network rate-of-rise and fixed temperature heat detector. Adopting the dual alarm mode, it is suitable for combustion heat emission status alarm of any object. When the environmental temperature goes up to the alarm threshold of 57 (135°F), or the rate of rise of temperature reaches 15°F (8) per minute,